7001 ACDGA/HCP4A
Super-precision, high-capacity, universally matchable single row angular contact ball bearingThese super-precision, high-capacity, single row angular contact ball bearings accommodate radial and axial loads acting simultaneously, where the axial load acts in one direction only. They are designed to accommodate heavy loads at relatively high speeds under low to moderate operating temperatures. Being universally matchable, they can be used together in arrangements to provide effective load sharing, within a predetermined preload range, without the use of shims or similar devices.
- Very high running accuracy
- Very high load carrying capacity
- Relatively high speed and stiffness
- Universally matchable
Description
| Universal matching bearing(s) | Yes, back-to-back (<>), face-to-face (><) or tandem (>>) |
Dimensions
| d | 12 mm | Bore diameter |
|---|---|---|
| D | 28 mm | Outside diameter |
| B | 8 mm | Width |
| d1 | 17.1 mm | Shoulder diameter of inner ring (large side face) |
| d2 | 17.1 mm | Shoulder diameter of inner ring (small side face) |
| D1 | 22.9 mm | Shoulder diameter of outer ring (large side face) |
| r1,2 | min. 0.3 mm | Chamfer dimension |
| r3,4 | min. 0.2 mm | Chamfer dimension |
| a | 8.7 mm | Distance from side face to pressure point |
Abutment dimensions
| da | min. 14 mm | Diameter of shaft abutment |
|---|---|---|
| db | min. 14 mm | Diameter of shaft abutment |
| Da | max. 26 mm | Diameter of housing abutment |
| Db | max. 26.6 mm | Diameter of housing abutment |
| ra | max. 0.3 mm | Radius of fillet |
| rb | max. 0.2 mm | Radius of fillet |
| dn | 18 mm | Position of oil nozzle |
Calculation data
| Basic dynamic load rating | C | 4.36 kN |
|---|---|---|
| Basic static load rating | C0 | 1.83 kN |
| Fatigue load limit | Pu | 0.057 kN |
| Contact angle | α | 25 ° |
| Ball diameter | Dw | 4.762 mm |
| Number of balls (per bearing) | z | 10 |
| Reference grease quantity (per bearing) | Gref | 0.27 cm³ |
| Preload class A | GA | 25 N |
|---|---|---|
| Axial stiffness for preload A (sets of two brgs back-to-back or face-to-face) | 38 N/µm |
| Correction factor dependent on bearing series and size | f | 1.03 |
|---|---|---|
| Correction factor dependent on contact angle | f1 | 0.99 |
| Correction factor, preload class A | f2A | 1 |
| Correction factor for hybrid bearings | fHC | 1.02 |
| Limiting value | e | 0.68 |
| Axial load factor (single, tandem) | Y1 | 0 |
| Axial load factor (single, tandem) | Y2 | 0.87 |
| Axial load factor (single, tandem) | Y0 | 0.38 |
| Radial load factor (single, tandem) | X1 | 1 |
| Radial load factor (single, tandem) | X2 | 0.41 |
| Radial load factor (single, tandem) | X0 | 0.5 |
| Axial load factor (back-to-back, face-to-face) | Y1 | 0.92 |
| Axial load factor (back-to-back, face-to-face) | Y2 | 1.41 |
| Axial load factor (back-to-back, face-to-face) | Y0 | 0.76 |
| Radial load factor (back-to-back, face-to-face) | X1 | 1 |
| Radial load factor (back-to-back, face-to-face) | X2 | 0.67 |
| Radial load factor (back-to-back, face-to-face) | X0 | 1 |
Mass
| Mass | 0.018 kg |
Tolerances and clearances
Product details
- Tolerances: P4A, P4B, P4, PA9A, P2
- Clamping and fitting forces: D design, E design, B design
- Designation suffixes H, H1, L and L1 identify variants for direct oil-air lubrication.
Principles of bearing selection and application
- Chamfer dimensions
- Seat tolerances for standard conditions: shafts, housings
- Values for ISO tolerance classes: shafts, housings
- Speed dependent initial grease fill → Initial grease fill
